Everett, MA · Middlesex County

Chimney Flashing Replacement Near me in Everett, MA

The joint where your chimney meets the roof fails before almost anything else on the house. We rebuild step and counter-flashing the right way — cut into the mortar, not smeared over it. Typical flashing repairs across Greater Boston run $400–$1,200, with full step-and-counter-flashing rebuilds on large chimneys or steep roofs pushing toward the top of that range.

Call (781) 653-5644

A surprising number of people searching for "chimney flashing replacement near me" are not reacting to a symptom at all — they are reacting to paperwork. A home inspector flagged something during a sale. An insurance carrier asked questions after a claim. An appraiser noted the chimney's condition. Chimneys sit at an awkward intersection of safety, structure, and liability, which is why they show up in so many transactions. Whether your search started with paperwork or with an actual problem, the underlying questions are the same: what is wrong, how serious is it, and what does a proper fix involve? Upside Down Chimney Sweeps answers all three below, drawing on the standards — NFPA 211 inspections in particular — that inspectors and insurers rely on. For documentation you can actually hand to a third party, call (781) 653-5644.

Homeowners insurance shapes chimney problems in ways people rarely anticipate. Most policies distinguish sharply between sudden, accidental events — a chimney fire, storm damage from a falling limb — and gradual deterioration, which carriers classify as deferred maintenance and typically decline to cover. That distinction puts the cost of neglect squarely on the homeowner. It also makes documentation valuable: a record of annual inspections per NFPA 211 demonstrates that a failure was genuinely sudden rather than years in the making, which can matter enormously during a claim. And if a chimney-related incident does occur, the insurer's first question is usually when the system was last inspected. Handling the problem behind your search promptly, and keeping the paperwork, protects both your house and your position if you ever need to file.

Massachusetts homes are old — genuinely old, not real-estate-listing old. Triple-deckers from the 1890s, Victorians with three flues in one stack, postwar capes with hastily added fireplaces: each era brought its own construction habits, and many predate flue liners entirely. An unlined or deteriorated flue lets heat and gases reach parts of the house they were never meant to touch. That is why this issue deserves more attention in a Massachusetts home than the same symptom might get in a newer build elsewhere. The original masons did excellent work with the materials of their time, but no chimney was designed to go a century without attention, and most around Greater Boston have outlived their builders by decades. Understanding your chimney's era is the first step toward understanding what is going wrong with it.

Chimney Flashing Repair in Everett, MA

Upside Down Chimney Sweeps rebuilds and repairs chimney flashing across Everett and the surrounding Greater Boston area from our home base in Melrose. We work both sides of the joint — mason enough to cut and repoint reglets correctly, roof-literate enough to weave steps into shingle courses without wrecking the field around them. Flashing sits exactly at the boundary where roofers and masons tend to point at each other; we take responsibility for the whole intersection instead. If you have stains near the chimney, a visible tar patch on the roof, or a roofer who told you the chimney is the problem, call (781) 653-5644 and we will get experienced eyes on it.

A correct installation has distinct layers with distinct jobs. Step flashing consists of L-shaped pieces of metal, one woven into each course of shingles as the roof climbs past the chimney, so every piece hands water down onto the shingle below it. Counter-flashing is the second layer: metal let into a groove — a reglet — cut into the chimney's mortar joints, then bent down over the tops of the step pieces. This counter-stepped arrangement means water running down the brick face is thrown out over the steps, never behind them, and neither layer depends on adhesive to do its job. An apron protects the downhill face, and on the uphill side a back pan or cricket diverts the water the chimney dams up.

Two parts of your house meet at the chimney's base, and they refuse to move together. The roof deck expands, contracts, and flexes with every temperature swing and snow load; the masonry chimney, anchored to its own foundation, barely moves at all. Any rigid seal between them is doomed from the day it is installed. That is the entire reason chimney flashing exists: instead of gluing the two structures together, a properly built flashing system overlaps layers of bent metal so water is shed by gravity while each layer stays free to move. Built right, it outlasts the shingles around it. Built wrong — or smeared over with tar — it becomes the single most common source of chimney leaks we see across Everett.

What the Service Includes

1Full flashing evaluation

We inspect the entire roof-to-chimney intersection from both sides: on the roof, we check step flashing engagement, counter-flashing seating, apron condition, fastener back-out, and any previous tar or caulk repairs; in the attic, we examine the sheathing and rafters around the chase for staining, delamination, and active moisture with a meter. Because flashing failures mimic crown and masonry leaks, we rule those out rather than assume. You get photos of everything and a straight answer about whether flashing is truly your problem — sometimes it is not, and we say so.

2Step flashing replacement

When steps are rusted, missing, or face-nailed through their vertical legs, we replace them properly. Shingle courses alongside the chimney are carefully lifted or removed, the old metal comes out, and new L-shaped steps go in — one per course, each overlapping the piece below, fastened to the deck rather than the masonry so the roof can move freely. Where conditions warrant, we bed the intersection in self-adhering ice-and-water membrane first, which matters enormously on the snow-loaded, ice-dam-prone rooflines common across Massachusetts.

3Counter-flashing cut into the mortar

This is the detail that separates a proper job from a caulk job. We grind a clean reglet into the mortar joints, following the joint line up the chimney in steps, insert the counter-flashing's bent edge into the groove, wedge it mechanically, and seal the joint with the right sealant — used as a gasket inside a groove, not as glue on a surface. Counter-flashing installed this way is held by the chimney itself and sheds water over the step flashing below it for decades.

4Crickets and saddles for wide chimneys

A chimney more than about 30 inches wide creates a dam on its uphill side, where snow, ice, and debris pile up and water ponds. Building convention and modern code guidance call for a cricket: a small peaked saddle framed behind the chimney that splits the flow and sends it around both sides. We fabricate and flash crickets on chimneys that never had one — common on the older housing stock around Everett — and rebuild failed ones. If your leak shows up on the chimney's high side, a missing cricket is a prime suspect.

5Material selection and upgrades

We work in aluminum, galvanized and stainless steel, copper, and lead-coated copper, and we will tell you honestly where each belongs. Aluminum is economical but should not sit against damp mortar for the long haul; copper costs more and can outlive two roofs; stainless shrugs off the coastal salt air that eats galvanized coatings in a decade. On historic homes we match existing copper work rather than mixing metals. The right choice depends on your roof's age, your budget, and your exposure — a coastal cape and an inland colonial do not get the same recommendation.

6Reglet repointing and roof integration

Flashing repair is masonry work as much as metal work. We repoint the joints we cut, match mortar color as closely as the wall allows, and address crumbling joints adjacent to the flashing line while we are up there — there is no sense seating new metal into failing mortar. We also coordinate cleanly with roofers: if your roof is being replaced, we can handle the chimney intersection as part of that project, and if we find shingle or decking problems beyond the flashing, we document them for your roofing contractor rather than pretending they do not exist.

How We Diagnose and Fix It

Professional chimney diagnosis follows a structure defined by NFPA 211, which recognizes three levels of inspection. A Level 1 inspection covers readily accessible portions of the chimney and is appropriate when nothing has changed and no problems are suspected — the standard annual checkup. A Level 2 inspection goes further: it adds accessible attics, basements, and crawl spaces, plus a video scan of the flue interior, and it is the prescribed level whenever a property is sold, a heating appliance changes, or an event like a chimney fire or severe storm may have caused damage. Level 3, rarely needed, involves opening up concealed areas of the structure. For the problem behind your search, a sweep will match the inspection level to the situation — and a symptom with an unknown cause generally justifies Level 2 scrutiny.

Fixing water intrusion is about sequence: seal the entry points from the top down, then protect the surfaces. That typically means crown repair or replacement first, since the crown is the chimney's roof; then a properly sized stainless cap to keep rain and animals out of the flue; then flashing — the layered metal where chimney meets roofline — repaired or replaced with counterflashing cut into the mortar joints rather than smeared over with roofing tar. Only after those are sound does waterproofing make sense: a vapor-permeable masonry water repellent that lets trapped moisture escape while blocking new absorption. Paint-like sealers that trap moisture inside brick actually accelerate freeze-thaw damage. Each layer protects the ones below it, which is why piecemeal fixes so often disappoint and a whole-system approach holds up for years.

Warning Signs to Watch For

Water stains on ceilings or walls adjacent to the chimney, especially after wind-driven rain.
Visible tar or roofing cement smeared around the chimney's base — evidence of a previous shortcut repair.
Rust streaks running from the chimney base down across the shingles.
Lifted, bent, or missing pieces of flashing after a windstorm.
Visible gaps between the counter-flashing and the mortar joint it should sit in.
Popped nails or loose fasteners along the flashing line.
Shingles that look wavy, curled, or spongy in the courses beside the chimney.
Attic sheathing that is dark, damp, or delaminating around the chimney — especially on its uphill side.
Leaks that appear during nor'easters but not during gentle vertical rain.
Moss or algae concentrated right at the roof-to-chimney intersection.

Why This Matters in Everett

Everett is one of the densest cities in the Commonwealth, built out almost entirely by the 1930s with triple-deckers, two-families, and closely spaced wood-frame singles. Most of these buildings carry original brick chimneys serving stacked heating appliances, and many flues have been switched from coal to oil to gas without ever being properly relined. Flat and low-pitch roofs are common, and access between buildings is tight.

Just four miles from our Melrose shop, Everett is home turf. The chimney story here is urban: aging multifamily stacks, gas-conversion liner work, and tall brick chimneys that loom over three stories of tenants who all depend on the same flue. Landlords and condo associations make up a big share of the calls in this city.

The single greatest enemy of masonry in Everett is not fire; it is water paired with our freeze-thaw climate. Brick and mortar are porous, and every rain or melting snowfall lets moisture soak in. When temperatures drop below freezing, that trapped water expands roughly nine percent, prying the material apart from within. When it thaws, the water sinks deeper into the newly opened pores and waits to freeze again. Massachusetts winters can cycle above and below freezing dozens of times, and each cycle does its increment of damage. The visible result is spalling: brick faces popping off, mortar joints crumbling, and crowns cracking. Keeping water out of the masonry in the first place is why caps, crowns, and waterproofing earn their keep here.

What It Typically Costs

An inspection is the least expensive service a chimney company offers and the one that determines everything else, so it is worth understanding what you are paying for. A proper inspection is methodical: firebox, damper, smoke chamber, accessible flue, crown, cap, flashing, and exterior masonry, all documented with photographs. Where conditions warrant, a video scan of the flue interior shows what no flashlight can, including cracked tiles and failed joints deep in the stack. The report you receive should let you make decisions calmly, with evidence, ranked by urgency. Paying for that clarity once a year, as NFPA 211 recommends, is what allows every other chimney dollar you spend to be spent on the right thing.

Why Call Upside Down Chimney Sweeps

Homeowners often delay a chimney sweep because they picture soot drifting across the living room. A professional sweep should be, and with us is, a clean process from start to finish. We lay drop cloths from the door to the hearth, seal the fireplace opening, and run a HEPA-filtered vacuum the entire time the brushes are working, so fine ash goes into the machine instead of onto your furniture. Our technicians treat your home the way they would want their own treated: shoe covers on, tools organized, and the workspace left exactly as we found it, minus the creosote. When we finish, the evidence that we were there is a cleaner flue and a written report, not a mess.

Frequently Asked Questions

What is chimney flashing, exactly?

Flashing is the layered sheet-metal system that waterproofs the joint where your chimney passes through the roof. Because the roof structure and the masonry move independently, no rigid or glued seal can survive there. Instead, flashing sheds water by overlapping: step flashing woven into the shingle courses carries water down the roof plane, and counter-flashing embedded in the chimney's mortar joints covers the tops of those steps so water running down the brick is thrown clear. Add an apron on the downhill face and a back pan or cricket uphill, and every side of the chimney has a gravity-fed drainage path. No adhesive is doing the real work — the geometry is.

What is the difference between step flashing and counter-flashing?

They are two layers with two jobs. Step flashing belongs to the roof: individual L-shaped pieces, one per shingle course, each tucked under a shingle and lapped over the piece below, fastened to the roof deck. It handles water flowing down the roof plane. Counter-flashing belongs to the chimney: pieces set into grooves cut in the mortar joints, bent down over the step flashing's vertical legs. It handles water flowing down the masonry face. The critical detail is that the two layers overlap without being attached to each other, so the roof and the chimney can move independently through the seasons without tearing the seal open.

Why not just seal it with roofing tar?

Roofing cement is a bandage, and everyone in this trade knows it. It bonds poorly to dusty masonry, turns brittle in the cold, shrinks away from edges within a couple of seasons, and — the part homeowners rarely hear — it can trap water behind it, holding moisture against the mortar through freeze-thaw cycles and accelerating the very damage it was hiding. It also buries the evidence, so the next diagnosis takes longer and costs more. We remove tar patches; we do not add to them. A proper counter-stepped metal system costs more on the day it is installed and dramatically less over the life of your roof.

Should I call a roofer or a chimney company for a flashing leak?

It is genuinely a boundary trade, which is why homeowners get bounced between the two. Roofers are excellent on the shingle side but often surface-mount counter-flashing with caulk rather than cutting it into the mortar, because masonry is not their trade. A chimney company that does masonry can cut reglets, repoint, and judge whether the leak is actually the crown or the brick rather than the flashing at all. We handle the full intersection and coordinate with your roofer when the job crosses into the roof field. Whoever you hire, ask one question: will the counter-flashing be let into the mortar joint? If the answer involves caulk, keep calling.

Which flashing metal is best, especially near the coast?

For most inland Greater Boston homes, aluminum or galvanized steel is serviceable and economical, but both have limits: aluminum reacts with damp mortar over time, and galvanized coatings fail early in salt air. Within a few miles of the ocean we push toward stainless steel or copper — coastal exposure corrodes cheap metal astonishingly fast, and we regularly replace galvanized flashing barely fifteen years old in shoreline towns. Copper is the premium choice everywhere: it forms beautifully, ages to a quiet brown, and routinely outlasts two shingle roofs. On historic homes in and around Everett, matching existing copper work is usually the right call both structurally and visually.

What is a cricket, and does my chimney need one?

A cricket, or saddle, is a small peaked structure built on the uphill side of a chimney to split water and snow around it instead of letting the chimney act as a dam. Modern building practice calls for one when the chimney is wider than about 30 inches across the slope. Without a cricket, the high side collects leaves, snowpack, and ponded water, and that standing load eventually beats any flat back pan. Many chimneys on older Massachusetts homes were built without one, which is why chronic high-side leaks are so common here. If your stains are on the uphill side of the chimney, ask us to check for this first.

How long does the repair take, and how long will it last?

Most full flashing rebuilds are a one-day job; targeted repairs of a single failed section often take a few hours. Weather matters — we want dry shingles, workable temperatures for sealants and mortar, and safe footing, so winter scheduling can shift with the forecast. As for longevity: properly counter-stepped metal set into sound mortar should last as long as the roof itself, and copper considerably longer. The honest caveat is the surrounding masonry — flashing set into crumbling joints will never reach its potential, which is why we repoint the reglet line as part of the job rather than treating it as an upsell.

My roof is being replaced — should the flashing be redone at the same time?

Yes, almost always, and the timing is a gift: with the shingles off, the entire intersection is exposed, membrane can be run properly, and new step flashing costs the least it ever will. Reusing old step flashing under a new roof is a common corner-cut we would talk you out of — thirty-year shingles deserve better than twenty-year-old metal. Coordinate the sequence: we can cut reglets and set counter-flashing right after the roofer finishes the field, or handle the full chimney intersection ourselves as part of the project. Call (781) 653-5644 before the roofing crew starts and we will slot the chimney work into their schedule.

Get It Handled Today

What you are really buying from a chimney company is the ability to stop wondering. No more second-guessing the flue every time you light a fire, no more eyeing that stain on the ceiling near the chimney, no more resolving each October to deal with it next year. One call to Upside Down Chimney Sweeps at (781) 653-5644 settles the question for your Everett home: a professional sweep, an inspection guided by NFPA 211, photographs of everything relevant, and recommendations ranked honestly by urgency. Most chimneys pass with minor notes, and their owners sleep better for knowing it. If yours needs work, you will know exactly what and why. Either way, the wondering ends.

Serving Everett Same-Week

Our Melrose shop is 4 miles from Everett. Call (781) 653-5644 for fast scheduling.

Call (781) 653-5644 Email Us

Mon–Sat: 7:00 AM – 7:00 PM · Emergency service available