Upside Down Chimney Sweeps logo
Call

Everett, MA · Middlesex County

Chimney Service Near me in Everett, MA

Cracked crowns, spalling brick, failed flashing, damaged flue tiles - we trace every chimney problem to its root cause and repair it properly, so you fix it once instead of chasing symptoms every spring. Most targeted chimney repairs in the Boston market run $400–$1,800 depending on access and scope, with crown and flashing work typically landing between $600 and $1,400 - we confirm exact numbers in a written estimate before any work begins.

Call (781) 653-5644

A typical call to our shop starts a lot like your search for "chimney service near me". A homeowner describes a symptom, often apologetically, unsure whether it is a real problem or something every chimney does. Our answer is almost always the same: chimneys do not develop symptoms for no reason, and the symptom you can see usually points to a cause you cannot. Upside Down Chimney Sweeps has been climbing ladders in and around Melrose long enough to know which noises, smells, stains, and drafts matter, and which just need a minor adjustment. In the sections below, we will walk through the likely causes behind your search, the way a professional confirms the real one, and what fixing it properly involves. When you are ready for eyes on your chimney, call (781) 653-5644.

In Massachusetts, a chimney is not seasonal decoration — it is infrastructure. The heating season here runs from October into April, and many chimneys serve double duty, venting a wood-burning fireplace on one flue and an oil or gas heating appliance on another. That means a chimney problem can compromise not just cozy fires but the system that keeps pipes from freezing in January. It also means the flues get real use: months of thermal cycling, condensation, and byproduct accumulation every single year. A problem that might stay dormant for a decade in a milder climate gets stress-tested here every winter. That is the practical reason Massachusetts homeowners cannot treat chimney symptoms casually — the season that reveals the problem is the same season you can least afford to lose the chimney.

Chimney problems compound in a way most home repairs do not. A roof leak generally stays a roof leak; a chimney defect recruits new ones. A cracked crown admits water, which spalls the top courses of brick, which opens mortar joints, which lets more water reach the flue tiles, which crack in turn — and suddenly a repair that once involved a trowel involves scaffolding. This cascade is the single best argument for acting early. In our experience around Greater Boston, the gap between catching a problem this season versus three seasons from now is frequently the difference between a minor line item and a partial rebuild. You do not need to panic over the issue that prompted your search, but you should resist the very human urge to file it under later.

Chimney Repair in Everett, MA

The housing stock around Greater Boston makes chimney repair its own specialty. A large share of the homes we service were built between the 1880s and the 1950s, with soft lime-based mortar, unlined or clay-tile flues, and chimneys that have already outlived several roofs. Many of these flues were later converted from coal or oil to gas, and the cooler, wetter gas exhaust condenses inside an oversized masonry flue, forming acidic moisture that quietly eats mortar joints and tile from the inside out. Add coastal salt air east of Route 1 and the aggressive freeze-thaw swings we get inland, and you have chimneys that need a technician who understands old New England masonry, not just a tube of caulk.

Upside Down Chimney Sweeps is based at 20 Sewall Street in Melrose, and we repair chimneys across Everett and the surrounding towns every week of the year. Our repair work starts with diagnosis, not guesswork: we follow NFPA 211 inspection practice, run a camera up the flue when the evidence calls for it, and document what we find with photos you can actually see. Then we explain the failure mechanism in plain language, give you a written scope and price, and fix the cause rather than smearing sealant over the symptom. If your chimney is leaking, shedding brick, or drafting poorly, call (781) 653-5644 and we will get eyes on it quickly.

Most chimney failures start in one of three places. The first is the crown, the concrete slab that caps the masonry at the top. Too many crowns were troweled out of leftover mortar with no overhang and no expansion gap around the flue tiles, so when the flue heats up and expands, it cracks the crown radially and lets water straight into the chimney core. The second is the mortar joints, which are designed to weather before the brick does. The third is the flashing, the layered metal system where chimney meets roof - when it was face-nailed and caulked instead of properly counter-stepped into the mortar joints, it is a leak waiting for its first hard rain.

What the Service Includes

1Crown Repair and Recasting

The crown sheds water away from the chimney core, and when it cracks, everything below it gets wet. For minor crazing we clean, fill, and coat the crown with a flexible elastomeric crown sealant that stays waterproof through freeze-thaw movement. For crowns that are broken, undersized, or poured flat with no overhang, we cast a proper new crown in concrete: sloped to shed water, projecting past the brick with a drip edge, and isolated from the flue tiles with a bond-break expansion joint so thermal movement cannot crack it again.

2Flashing Repair and Counter-Flashing

Flashing failures cause more "mystery leaks" than any other chimney defect, and they are often misdiagnosed as roof problems. We rebuild the system the correct way: step flashing woven into each shingle course against the chimney, then counter-flashing cut into a reglet ground into the mortar joints and lapped down over the steps. Water running down the brick face passes over metal, never behind it. On wide chimneys on the low side of a roof, we can also add a cricket to divert water and snow load around the stack.

3Spalling Brick Replacement

When the fired face of a brick pops off - spalling - the softer core underneath absorbs water even faster, and the damage accelerates. We cut out spalled and shattered brick individually, source replacement brick that matches the original in size, color, and hardness, and lay them in mortar matched to the existing wall. This matters in Everett, where many chimneys were built with older, softer brick; setting hard modern brick and Portland-rich mortar into a soft old chimney concentrates stress and causes the surrounding original masonry to fail next.

4Firebox and Smoke Chamber Repair

Inside the fireplace, we repair cracked firebrick and deteriorated refractory mortar joints in the firebox, where temperatures demand materials rated for direct flame contact. Above it, we parge rough, corbelled smoke chambers with insulating refractory mortar to create the smooth, sealed funnel NFPA 211 calls for. An unparged smoke chamber leaks heat and combustion gases into the surrounding structure and catches creosote on every ledge. This is one of the most commonly flagged defects in older Massachusetts fireplaces, and one of the most important to correct.

5Damper and Cap Repair or Replacement

A rusted-open throat damper pours heated indoor air up the flue all winter; a rusted-shut one makes the fireplace unusable. We repair or replace throat dampers, and where the original is beyond saving we install top-sealing dampers that close the flue at the crown with a silicone gasket - tighter than any throat damper. We also repair or replace chimney caps, the stainless covers that keep rain, snow, squirrels, and nesting birds out of an open flue. A missing cap is the cheapest problem to fix and the most expensive to ignore.

6Flue Tile and Liner Repairs

Cracked or shifted clay flue tiles let heat and combustion gases reach the wood framing around the chimney, which is exactly the failure path in many chimney-related house fires. After a camera scan locates the damage, we advise honestly: isolated joint deterioration can sometimes be resurfaced, but cracked tiles typically call for relining with a UL-listed stainless steel liner sized to the appliance. We install insulated stainless systems for wood, oil, and gas flues, restoring a continuous, code-compliant path from appliance to chimney top.

How We Diagnose and Fix It

Draft problems get diagnosed by treating the chimney as what it is — one half of a system that includes the whole house. The sweep evaluates flue size relative to the fireplace opening, damper operation, smoke chamber geometry, cap and termination height, and nearby rooflines or trees that create wind pressure zones. Then comes the house side: modern weatherization can seal a home so tightly that the chimney cannot pull enough replacement air, and competing exhausts like range hoods or bath fans can win the tug-of-war and drag smoke backward into the room. A few controlled tests — a smoke pencil at the fireplace opening, observing draft with windows cracked versus sealed — usually isolate the culprit quickly. It is methodical elimination, not guesswork, and it is why draft complaints rarely have the cause homeowners first assume.

Masonry repairs succeed or fail on materials and prep, not just workmanship. Repointing — cutting out failed mortar joints and refilling them — only lasts when the new mortar matches the old in hardness; modern Portland-heavy mixes are actually too strong for older Massachusetts brick and cause the surrounding faces to spall. Crown work has its own rules: a proper crown is cast concrete with an overhang and drip edge, not a thin mortar wash troweled over the top course, and a badly failed crown gets rebuilt rather than endlessly patched. Spalled bricks are cut out and replaced individually where damage is contained. When chimney repair is on the table, ask the contractor what mortar type they intend to use and why — the answer tells you quickly whether you are dealing with a chimney specialist or a generalist.

Warning Signs to Watch For

  • White, chalky staining (efflorescence) on the brick, which means water is moving through the masonry and carrying salts to the surface.
  • Brick faces flaking, popping, or collecting as chips in the yard or on the roof - classic freeze-thaw spalling.
  • A ceiling or wall stain near the chimney that appears during wind-driven rain, the signature of failed flashing.
  • Cracks, gaps, or missing chunks visible in the crown when you look at the chimney top from the ground or a photo.
  • Crumbling or recessed mortar joints you can rake out with a fingertip.
  • Pieces of clay tile or gray flue debris landing in the fireplace or on the smoke shelf.
  • A damper that is rusted, hard to operate, or no longer seals - often a sign water has been entering from above.
  • A musty, campfire, or damp-masonry odor from the fireplace, especially in humid summer weather.
  • Smoke entering the room, or a fireplace that has become noticeably harder to start and keep drafting.
  • Rust streaks on the chimney exterior or on the firebox floor, meaning a cap, chase cover, or flashing component is corroding.

Why This Matters in Everett

Everett is one of the densest cities in the Commonwealth, built out almost entirely by the 1930s with triple-deckers, two-families, and closely spaced wood-frame singles. Most of these buildings carry original brick chimneys serving stacked heating appliances, and many flues have been switched from coal to oil to gas without ever being properly relined. Flat and low-pitch roofs are common, and access between buildings is tight.

Just four miles from our Melrose shop, Everett is home turf. The chimney story here is urban: aging multifamily stacks, gas-conversion liner work, and tall brick chimneys that loom over three stories of tenants who all depend on the same flue. Landlords and condo associations make up a big share of the calls in this city.

The single greatest enemy of masonry in Everett is not fire; it is water paired with our freeze-thaw climate. Brick and mortar are porous, and every rain or melting snowfall lets moisture soak in. When temperatures drop below freezing, that trapped water expands roughly nine percent, prying the material apart from within. When it thaws, the water sinks deeper into the newly opened pores and waits to freeze again. Massachusetts winters can cycle above and below freezing dozens of times, and each cycle does its increment of damage. The visible result is spalling: brick faces popping off, mortar joints crumbling, and crowns cracking. Keeping water out of the masonry in the first place is why caps, crowns, and waterproofing earn their keep here.

What It Typically Costs

The best defense against overpaying for chimney work is a contractor who shows their evidence, so here is what you should demand from anyone in our trade, including us. Ask to see photographs or video of the condition being repaired. Ask which part of NFPA 211 or the appliance manufacturer's requirements makes the work necessary rather than optional. Ask for a written, itemized estimate before work begins, and ask what happens to the price if hidden conditions appear. A reputable company answers all of this comfortably. Chimney work is invisible to the homeowner almost by definition, which is exactly why documentation, plain explanations, and written scope are not courtesies; they are the actual product.

Why Call Upside Down Chimney Sweeps

Plenty of companies will run a brush through your flue. What sets Upside Down Chimney Sweeps apart is everything that happens around the brush. We document our inspections with photographs, so you see exactly what we see inside your smoke chamber and up your flue. We explain findings against the actual language of NFPA 211 rather than vague warnings. We give written estimates before repair work begins, not after. And because we are a local outfit based in Melrose rather than a franchise dispatching strangers, the technician in your driveway has a personal stake in doing the job right. Our business grows on referrals between neighbors, which is exactly the kind of pressure a homeowner should want a contractor to feel.

Frequently Asked Questions

How do I know if my chimney needs repair or if it can wait?
The honest answer is that you usually cannot tell from the ground, because the failures that matter most - crown cracks, flashing gaps, cracked flue tiles - are invisible from the yard. What you can trust are the secondary symptoms: staining, spalled brick chips, leaks during storms, flue debris in the firebox, or odors. Any one of those means water or combustion gases are going somewhere they should not, and waiting always increases the repair scope. The low-risk move is an inspection: we document the chimney's actual condition with photos, tell you what genuinely can wait, and put numbers on what cannot. Homeowners in Everett are often relieved to learn the fix is smaller than they feared.
Why is my chimney leaking when the roof was just replaced?
This is one of the most common calls we get, and the answer is usually flashing. Roofing crews are excellent at shingles but frequently reuse old counter-flashing or rely on surface-mounted metal and caulk, which fails as soon as the sealant shrinks. Correct chimney flashing is a two-part system: step flashing woven into the shingle courses, covered by counter-flashing that is let into a groove cut in the mortar joints and lapped over the steps. Water crossing the joint always lands on metal. Beyond flashing, a cracked crown, porous brick, or a missing cap can each mimic a roof leak. We test methodically so you repair the actual entry point, not the loudest suspect.
What is spalling and why does it happen so much in Massachusetts?
Spalling is when the hard fired face of a brick breaks away, leaving the soft, sandy core exposed. The mechanism is freeze-thaw: brick absorbs water through its face and through open mortar joints, and when temperatures drop, that trapped water freezes and expands about nine percent, popping the face off from behind. Massachusetts is close to a worst-case climate for this - we routinely swing across the freezing line dozens of times each winter, and coastal towns add salt-laden air that accelerates the damage. Once a brick spalls, it absorbs water faster, so deterioration snowballs. We replace spalled brick, correct the moisture source, and often recommend a breathable water repellent to slow future absorption.
Can you just seal or waterproof the chimney instead of repairing it?
Sealing has a legitimate place, but only on sound masonry. A vapor-permeable siloxane water repellent slows how fast brick absorbs rain while still letting internal moisture escape - applied over open joints or a cracked crown, it merely hides the problem while water keeps entering through the defects. Worse, a non-breathable film sealer can trap moisture inside the wall and make freeze-thaw spalling dramatically worse. Our sequence is repair first, then protect: fix the crown, flashing, joints, and any damaged brick, then apply the repellent as insurance. If a company proposes spraying your chimney without repairing visible defects first, get a second opinion before you pay for it.
Are chimney repairs covered by homeowners insurance?
It depends on the cause, and the distinction matters. Sudden, accidental events - a chimney fire, a lightning strike, a tree limb brought down in a nor'easter - are commonly covered perils. Gradual deterioration from age, water intrusion, and freeze-thaw is treated as maintenance and typically is not covered. Where documentation helps is the gray area: a storm-damaged crown, or interior damage discovered after a specific event. We provide dated photos, written findings, and repair scopes that adjusters can actually use, and many clients in Everett have used our inspection reports to support legitimate claims. We cannot promise coverage, but we can make sure your file is solid.
How long do chimney repairs take, and can they be done in winter?
Most single-issue repairs - a crown recast, flashing rebuild, damper replacement, or a course of brick replacement - are completed in one day. Larger combined scopes usually run two to three days. Winter work is possible but constrained: mortar and crown concrete need adequate temperatures to cure properly, so masonry work in freezing weather requires cold-weather methods, tenting, or sometimes a wait for a thaw window. Flashing repairs, caps, dampers, and liner work can proceed through most winter conditions. If you discover a problem in January, call (781) 653-5644 anyway - we can often stabilize the chimney immediately and schedule permanent masonry for the first suitable stretch of weather.
What is the difference between a Level 1 and Level 2 inspection?
NFPA 211 defines three inspection levels. A Level 1 is the annual check for a chimney in continuous service with no changes: readily accessible areas, verifying the flue is sound, clear, and appliance-appropriate. A Level 2 goes further and includes a video scan of the flue interior plus accessible attic, crawlspace, and roof areas - it is called for when property is sold or transferred, when an appliance or fuel type changes, or after an operating malfunction or external event like a chimney fire or severe storm. For repair diagnosis, Level 2 is often the right tool, because the camera finds cracked tiles and hidden defects that no flashlight ever will.
Why should I choose a local company for chimney repair?
Because the chimneys here are unlike chimneys almost anywhere else. Working out of Melrose, we spend every season inside the same housing stock you own - Victorians with soft lime mortar, triple-deckers with shared flues, 1950s capes converted from oil to gas - and we know exactly how these systems fail in this climate. That local pattern recognition means faster, more accurate diagnosis and repairs matched to the original materials rather than generic fixes. We are also twenty minutes away when something goes wrong, and our reputation in Everett rides on every roof we touch. Storm-chasing outfits leave town; we drive past our work daily.

Get It Handled Today

You searched for chimney service near me, and the search can end here. Upside Down Chimney Sweeps handles this work for Everett homeowners regularly, following NFPA 211 standards, documenting everything with photographs, and explaining findings without jargon or pressure. Call (781) 653-5644 to talk through your situation with someone who does this every day; a few minutes on the phone is usually enough to scope the visit and set a time. We show up when promised, protect your home while we work, and stand behind the results. There are certainly bigger companies and flashier websites out there, but for careful chimney work done close to home, we like our chances of earning your call and then keeping your business.

Serving Everett Same-Week

Our Melrose shop is 4 miles from Everett. Call (781) 653-5644 for fast scheduling.

Call (781) 653-5644Email Us

Mon–Sat: 7:00 AM – 7:00 PM · Emergency service available