Burlington, MA · Middlesex County

Leak Around Chimney Flashing in Burlington, MA

The joint where your chimney meets the roof fails before almost anything else on the house. We rebuild step and counter-flashing the right way — cut into the mortar, not smeared over it. Typical flashing repairs across Greater Boston run $400–$1,200, with full step-and-counter-flashing rebuilds on large chimneys or steep roofs pushing toward the top of that range.

Call (781) 653-5644

Every autumn, searches for "leak around chimney flashing" spike across Greater Boston, and every autumn our phone at (781) 653-5644 rings with some version of the same story: the first cold night arrived, someone lit the first fire of the season, and something was clearly wrong. Chimneys have a way of announcing their problems exactly when you need them most. The good news is that most of these problems are well understood, diagnosable in a single visit, and fixable before deep winter sets in — provided you do not wait until December, when every sweep in Massachusetts is booked solid. This article from Upside Down Chimney Sweeps lays out what the issue behind your search typically is, how we confirm it, what the repair involves, and how to time the work sensibly so the fireplace is ready when the cold is.

In Massachusetts, a chimney is not seasonal decoration — it is infrastructure. The heating season here runs from October into April, and many chimneys serve double duty, venting a wood-burning fireplace on one flue and an oil or gas heating appliance on another. That means a chimney problem can compromise not just cozy fires but the system that keeps pipes from freezing in January. It also means the flues get real use: months of thermal cycling, condensation, and byproduct accumulation every single year. A problem that might stay dormant for a decade in a milder climate gets stress-tested here every winter. That is the practical reason Massachusetts homeowners cannot treat chimney symptoms casually — the season that reveals the problem is the same season you can least afford to lose the chimney.

Ask any experienced sweep to name the real enemy of chimneys and the answer will not be fire — it will be water. Masonry is porous. Rain and snowmelt soak into brick and mortar, and every time temperatures cross freezing, that trapped water expands roughly nine percent, prying material apart from the inside. In a Massachusetts winter, a single week can deliver several freeze-thaw cycles. The chimney's defenses against this — the crown on top, the cap over the flue, the flashing where brick meets roof, and breathable water repellents on the masonry face — all wear out on their own schedules. When any one fails, water gets in, and nearly every expensive chimney problem we see traces back to that moment. Whatever symptom brought you here, water is the first suspect worth ruling out.

Chimney Flashing Repair in Burlington, MA

A correct installation has distinct layers with distinct jobs. Step flashing consists of L-shaped pieces of metal, one woven into each course of shingles as the roof climbs past the chimney, so every piece hands water down onto the shingle below it. Counter-flashing is the second layer: metal let into a groove — a reglet — cut into the chimney's mortar joints, then bent down over the tops of the step pieces. This counter-stepped arrangement means water running down the brick face is thrown out over the steps, never behind them, and neither layer depends on adhesive to do its job. An apron protects the downhill face, and on the uphill side a back pan or cricket diverts the water the chimney dams up.

Two parts of your house meet at the chimney's base, and they refuse to move together. The roof deck expands, contracts, and flexes with every temperature swing and snow load; the masonry chimney, anchored to its own foundation, barely moves at all. Any rigid seal between them is doomed from the day it is installed. That is the entire reason chimney flashing exists: instead of gluing the two structures together, a properly built flashing system overlaps layers of bent metal so water is shed by gravity while each layer stays free to move. Built right, it outlasts the shingles around it. Built wrong — or smeared over with tar — it becomes the single most common source of chimney leaks we see across Burlington.

Around Boston, flashing dies in predictable ways. Galvanized steel rusts through — faster near the coast, where salt air is relentless. Counter-flashing that was surface-mounted with caulk instead of cut into the mortar peels away as the sealant fails. Nails back out of step flashing as the decking flexes through the seasons. Ice dams push meltwater up-slope and sideways, finding laps that shed downhill flow perfectly well. And on a remarkable number of roofs we inspect, someone has already answered a leak with roofing cement — a repair that buys a season or two, traps water behind it, and makes the eventual proper repair messier. If your chimney wears a black tar collar, water has been in there before.

What the Service Includes

1Full flashing evaluation

We inspect the entire roof-to-chimney intersection from both sides: on the roof, we check step flashing engagement, counter-flashing seating, apron condition, fastener back-out, and any previous tar or caulk repairs; in the attic, we examine the sheathing and rafters around the chase for staining, delamination, and active moisture with a meter. Because flashing failures mimic crown and masonry leaks, we rule those out rather than assume. You get photos of everything and a straight answer about whether flashing is truly your problem — sometimes it is not, and we say so.

2Step flashing replacement

When steps are rusted, missing, or face-nailed through their vertical legs, we replace them properly. Shingle courses alongside the chimney are carefully lifted or removed, the old metal comes out, and new L-shaped steps go in — one per course, each overlapping the piece below, fastened to the deck rather than the masonry so the roof can move freely. Where conditions warrant, we bed the intersection in self-adhering ice-and-water membrane first, which matters enormously on the snow-loaded, ice-dam-prone rooflines common across Massachusetts.

3Counter-flashing cut into the mortar

This is the detail that separates a proper job from a caulk job. We grind a clean reglet into the mortar joints, following the joint line up the chimney in steps, insert the counter-flashing's bent edge into the groove, wedge it mechanically, and seal the joint with the right sealant — used as a gasket inside a groove, not as glue on a surface. Counter-flashing installed this way is held by the chimney itself and sheds water over the step flashing below it for decades.

4Crickets and saddles for wide chimneys

A chimney more than about 30 inches wide creates a dam on its uphill side, where snow, ice, and debris pile up and water ponds. Building convention and modern code guidance call for a cricket: a small peaked saddle framed behind the chimney that splits the flow and sends it around both sides. We fabricate and flash crickets on chimneys that never had one — common on the older housing stock around Burlington — and rebuild failed ones. If your leak shows up on the chimney's high side, a missing cricket is a prime suspect.

5Material selection and upgrades

We work in aluminum, galvanized and stainless steel, copper, and lead-coated copper, and we will tell you honestly where each belongs. Aluminum is economical but should not sit against damp mortar for the long haul; copper costs more and can outlive two roofs; stainless shrugs off the coastal salt air that eats galvanized coatings in a decade. On historic homes we match existing copper work rather than mixing metals. The right choice depends on your roof's age, your budget, and your exposure — a coastal cape and an inland colonial do not get the same recommendation.

6Reglet repointing and roof integration

Flashing repair is masonry work as much as metal work. We repoint the joints we cut, match mortar color as closely as the wall allows, and address crumbling joints adjacent to the flashing line while we are up there — there is no sense seating new metal into failing mortar. We also coordinate cleanly with roofers: if your roof is being replaced, we can handle the chimney intersection as part of that project, and if we find shingle or decking problems beyond the flashing, we document them for your roofing contractor rather than pretending they do not exist.

How We Diagnose and Fix It

Water problems are the most misdiagnosed issues in the chimney world, because water travels. It enters at one point — a crown crack, a flashing gap, porous brick faces — then follows flue tiles, framing, and wall cavities before appearing as a stain somewhere that may be rooms away. A proper moisture diagnosis therefore refuses to trust the stain. The sweep examines every entry point in order: crown, cap, flashing, masonry surfaces, and the condition of any existing water repellent, often correlating findings with which weather conditions produce the symptom. Wind-driven rain from a nor'easter implicates different entry points than a slow soaking storm does. Getting this right the first time matters, because the most common expensive mistake in chimney leak repair is sealing the wrong thing and waiting a season to find out.

Fixing water intrusion is about sequence: seal the entry points from the top down, then protect the surfaces. That typically means crown repair or replacement first, since the crown is the chimney's roof; then a properly sized stainless cap to keep rain and animals out of the flue; then flashing — the layered metal where chimney meets roofline — repaired or replaced with counterflashing cut into the mortar joints rather than smeared over with roofing tar. Only after those are sound does waterproofing make sense: a vapor-permeable masonry water repellent that lets trapped moisture escape while blocking new absorption. Paint-like sealers that trap moisture inside brick actually accelerate freeze-thaw damage. Each layer protects the ones below it, which is why piecemeal fixes so often disappoint and a whole-system approach holds up for years.

Warning Signs to Watch For

Water stains on ceilings or walls adjacent to the chimney, especially after wind-driven rain.
Visible tar or roofing cement smeared around the chimney's base — evidence of a previous shortcut repair.
Rust streaks running from the chimney base down across the shingles.
Lifted, bent, or missing pieces of flashing after a windstorm.
Visible gaps between the counter-flashing and the mortar joint it should sit in.
Popped nails or loose fasteners along the flashing line.
Shingles that look wavy, curled, or spongy in the courses beside the chimney.
Attic sheathing that is dark, damp, or delaminating around the chimney — especially on its uphill side.
Leaks that appear during nor'easters but not during gentle vertical rain.
Moss or algae concentrated right at the roof-to-chimney intersection.

Why This Matters in Burlington

Burlington transformed from farm town to suburb almost entirely after World War II, so its streets are lined with 1950s-1970s capes, ranches, and splits, most built with a single central brick chimney and fireplace. Teardown-and-rebuild activity in recent years has added newer colonials with gas fireplaces. The original mid-century chimneys are now uniformly at the age where crowns, caps, and mortar joints need attention.

Because nearly all of Burlington was built within the same few decades, its chimneys are aging on the same schedule, and whole neighborhoods hit the repointing and crown-repair stage together. Home turnover driven by the Route 128 job market also means a steady flow of pre-sale inspections that uncover decades of deferred maintenance.

Spring is when winter sends Burlington homeowners the bill. As temperatures stabilize, the damage done by months of freeze-thaw cycling becomes visible: hairline crown cracks that widened, mortar joints that crumble at a touch, brick faces flaked off onto the roof, and white mineral staining called efflorescence, which is a chimney's way of announcing that water is moving through its masonry and leaving dissolved salts behind on the surface. None of these symptoms improves on its own, and all of them worsen faster once water has an established path. A spring inspection catches the winter's damage at its cheapest stage, and leaves the whole summer, the best season for masonry work, to repair it properly.

What It Typically Costs

Chimney repair pricing varies more than sweep pricing because chimneys fail in such different ways and places. The main drivers are extent, access, and materials. Repointing a few mortar joints is a different undertaking from rebuilding a chimney from the roofline up. Work high on a steep roof may require staging that a walk-up ranch never would. And in the older neighborhoods we serve, matching brick and mortar appropriately matters, both for appearance and because modern mortar that is harder than antique brick can actually accelerate damage to the original masonry. A written estimate after an actual inspection is the only number worth trusting, and it should itemize the work plainly enough to compare against any other bid.

Why Call Upside Down Chimney Sweeps

Homeowners often delay a chimney sweep because they picture soot drifting across the living room. A professional sweep should be, and with us is, a clean process from start to finish. We lay drop cloths from the door to the hearth, seal the fireplace opening, and run a HEPA-filtered vacuum the entire time the brushes are working, so fine ash goes into the machine instead of onto your furniture. Our technicians treat your home the way they would want their own treated: shoe covers on, tools organized, and the workspace left exactly as we found it, minus the creosote. When we finish, the evidence that we were there is a cleaner flue and a written report, not a mess.

Frequently Asked Questions

What is chimney flashing, exactly?

Flashing is the layered sheet-metal system that waterproofs the joint where your chimney passes through the roof. Because the roof structure and the masonry move independently, no rigid or glued seal can survive there. Instead, flashing sheds water by overlapping: step flashing woven into the shingle courses carries water down the roof plane, and counter-flashing embedded in the chimney's mortar joints covers the tops of those steps so water running down the brick is thrown clear. Add an apron on the downhill face and a back pan or cricket uphill, and every side of the chimney has a gravity-fed drainage path. No adhesive is doing the real work — the geometry is.

What is the difference between step flashing and counter-flashing?

They are two layers with two jobs. Step flashing belongs to the roof: individual L-shaped pieces, one per shingle course, each tucked under a shingle and lapped over the piece below, fastened to the roof deck. It handles water flowing down the roof plane. Counter-flashing belongs to the chimney: pieces set into grooves cut in the mortar joints, bent down over the step flashing's vertical legs. It handles water flowing down the masonry face. The critical detail is that the two layers overlap without being attached to each other, so the roof and the chimney can move independently through the seasons without tearing the seal open.

Why not just seal it with roofing tar?

Roofing cement is a bandage, and everyone in this trade knows it. It bonds poorly to dusty masonry, turns brittle in the cold, shrinks away from edges within a couple of seasons, and — the part homeowners rarely hear — it can trap water behind it, holding moisture against the mortar through freeze-thaw cycles and accelerating the very damage it was hiding. It also buries the evidence, so the next diagnosis takes longer and costs more. We remove tar patches; we do not add to them. A proper counter-stepped metal system costs more on the day it is installed and dramatically less over the life of your roof.

Should I call a roofer or a chimney company for a flashing leak?

It is genuinely a boundary trade, which is why homeowners get bounced between the two. Roofers are excellent on the shingle side but often surface-mount counter-flashing with caulk rather than cutting it into the mortar, because masonry is not their trade. A chimney company that does masonry can cut reglets, repoint, and judge whether the leak is actually the crown or the brick rather than the flashing at all. We handle the full intersection and coordinate with your roofer when the job crosses into the roof field. Whoever you hire, ask one question: will the counter-flashing be let into the mortar joint? If the answer involves caulk, keep calling.

Which flashing metal is best, especially near the coast?

For most inland Greater Boston homes, aluminum or galvanized steel is serviceable and economical, but both have limits: aluminum reacts with damp mortar over time, and galvanized coatings fail early in salt air. Within a few miles of the ocean we push toward stainless steel or copper — coastal exposure corrodes cheap metal astonishingly fast, and we regularly replace galvanized flashing barely fifteen years old in shoreline towns. Copper is the premium choice everywhere: it forms beautifully, ages to a quiet brown, and routinely outlasts two shingle roofs. On historic homes in and around Burlington, matching existing copper work is usually the right call both structurally and visually.

What is a cricket, and does my chimney need one?

A cricket, or saddle, is a small peaked structure built on the uphill side of a chimney to split water and snow around it instead of letting the chimney act as a dam. Modern building practice calls for one when the chimney is wider than about 30 inches across the slope. Without a cricket, the high side collects leaves, snowpack, and ponded water, and that standing load eventually beats any flat back pan. Many chimneys on older Massachusetts homes were built without one, which is why chronic high-side leaks are so common here. If your stains are on the uphill side of the chimney, ask us to check for this first.

How long does the repair take, and how long will it last?

Most full flashing rebuilds are a one-day job; targeted repairs of a single failed section often take a few hours. Weather matters — we want dry shingles, workable temperatures for sealants and mortar, and safe footing, so winter scheduling can shift with the forecast. As for longevity: properly counter-stepped metal set into sound mortar should last as long as the roof itself, and copper considerably longer. The honest caveat is the surrounding masonry — flashing set into crumbling joints will never reach its potential, which is why we repoint the reglet line as part of the job rather than treating it as an upsell.

My roof is being replaced — should the flashing be redone at the same time?

Yes, almost always, and the timing is a gift: with the shingles off, the entire intersection is exposed, membrane can be run properly, and new step flashing costs the least it ever will. Reusing old step flashing under a new roof is a common corner-cut we would talk you out of — thirty-year shingles deserve better than twenty-year-old metal. Coordinate the sequence: we can cut reglets and set counter-flashing right after the roofer finishes the field, or handle the full chimney intersection ourselves as part of the project. Call (781) 653-5644 before the roofing crew starts and we will slot the chimney work into their schedule.

Get It Handled Today

A well-maintained chimney is one of those quiet protections a house provides its family, like a sound roof or a dry basement, invisible right up until the moment it matters. Giving your Burlington home that protection takes remarkably little: an annual inspection, sweeping whenever the flue needs it, and small repairs made before winter can enlarge them. Upside Down Chimney Sweeps would be honored to be the company you trust with that work, and starting is as simple as calling (781) 653-5644. We will treat your home with care, your questions with patience, and your budget with respect. The fires will feel better once you know for certain what condition their chimney is really in.

Serving Burlington Same-Week

Our Melrose shop is 10 miles from Burlington. Call (781) 653-5644 for fast scheduling.

Call (781) 653-5644 Email Us

Mon–Sat: 7:00 AM – 7:00 PM · Emergency service available