Georgetown, MA · Essex County

Leak Around Chimney Flashing in Georgetown, MA

The joint where your chimney meets the roof fails before almost anything else on the house. We rebuild step and counter-flashing the right way — cut into the mortar, not smeared over it. Typical flashing repairs across Greater Boston run $400–$1,200, with full step-and-counter-flashing rebuilds on large chimneys or steep roofs pushing toward the top of that range.

Call (781) 653-5644

A typical call to our shop starts a lot like your search for "leak around chimney flashing". A homeowner describes a symptom, often apologetically, unsure whether it is a real problem or something every chimney does. Our answer is almost always the same: chimneys do not develop symptoms for no reason, and the symptom you can see usually points to a cause you cannot. Upside Down Chimney Sweeps has been climbing ladders in and around Melrose long enough to know which noises, smells, stains, and drafts matter, and which just need a minor adjustment. In the sections below, we will walk through the likely causes behind your search, the way a professional confirms the real one, and what fixing it properly involves. When you are ready for eyes on your chimney, call (781) 653-5644.

Chimney problems compound in a way most home repairs do not. A roof leak generally stays a roof leak; a chimney defect recruits new ones. A cracked crown admits water, which spalls the top courses of brick, which opens mortar joints, which lets more water reach the flue tiles, which crack in turn — and suddenly a repair that once involved a trowel involves scaffolding. This cascade is the single best argument for acting early. In our experience around Greater Boston, the gap between catching a problem this season versus three seasons from now is frequently the difference between a minor line item and a partial rebuild. You do not need to panic over the issue that prompted your search, but you should resist the very human urge to file it under later.

Massachusetts homes are old — genuinely old, not real-estate-listing old. Triple-deckers from the 1890s, Victorians with three flues in one stack, postwar capes with hastily added fireplaces: each era brought its own construction habits, and many predate flue liners entirely. An unlined or deteriorated flue lets heat and gases reach parts of the house they were never meant to touch. That is why this issue deserves more attention in a Massachusetts home than the same symptom might get in a newer build elsewhere. The original masons did excellent work with the materials of their time, but no chimney was designed to go a century without attention, and most around Greater Boston have outlived their builders by decades. Understanding your chimney's era is the first step toward understanding what is going wrong with it.

Chimney Flashing Repair in Georgetown, MA

Two parts of your house meet at the chimney's base, and they refuse to move together. The roof deck expands, contracts, and flexes with every temperature swing and snow load; the masonry chimney, anchored to its own foundation, barely moves at all. Any rigid seal between them is doomed from the day it is installed. That is the entire reason chimney flashing exists: instead of gluing the two structures together, a properly built flashing system overlaps layers of bent metal so water is shed by gravity while each layer stays free to move. Built right, it outlasts the shingles around it. Built wrong — or smeared over with tar — it becomes the single most common source of chimney leaks we see across Georgetown.

Upside Down Chimney Sweeps rebuilds and repairs chimney flashing across Georgetown and the surrounding Greater Boston area from our home base in Melrose. We work both sides of the joint — mason enough to cut and repoint reglets correctly, roof-literate enough to weave steps into shingle courses without wrecking the field around them. Flashing sits exactly at the boundary where roofers and masons tend to point at each other; we take responsibility for the whole intersection instead. If you have stains near the chimney, a visible tar patch on the roof, or a roofer who told you the chimney is the problem, call (781) 653-5644 and we will get experienced eyes on it.

Around Boston, flashing dies in predictable ways. Galvanized steel rusts through — faster near the coast, where salt air is relentless. Counter-flashing that was surface-mounted with caulk instead of cut into the mortar peels away as the sealant fails. Nails back out of step flashing as the decking flexes through the seasons. Ice dams push meltwater up-slope and sideways, finding laps that shed downhill flow perfectly well. And on a remarkable number of roofs we inspect, someone has already answered a leak with roofing cement — a repair that buys a season or two, traps water behind it, and makes the eventual proper repair messier. If your chimney wears a black tar collar, water has been in there before.

What the Service Includes

1Full flashing evaluation

We inspect the entire roof-to-chimney intersection from both sides: on the roof, we check step flashing engagement, counter-flashing seating, apron condition, fastener back-out, and any previous tar or caulk repairs; in the attic, we examine the sheathing and rafters around the chase for staining, delamination, and active moisture with a meter. Because flashing failures mimic crown and masonry leaks, we rule those out rather than assume. You get photos of everything and a straight answer about whether flashing is truly your problem — sometimes it is not, and we say so.

2Step flashing replacement

When steps are rusted, missing, or face-nailed through their vertical legs, we replace them properly. Shingle courses alongside the chimney are carefully lifted or removed, the old metal comes out, and new L-shaped steps go in — one per course, each overlapping the piece below, fastened to the deck rather than the masonry so the roof can move freely. Where conditions warrant, we bed the intersection in self-adhering ice-and-water membrane first, which matters enormously on the snow-loaded, ice-dam-prone rooflines common across Massachusetts.

3Counter-flashing cut into the mortar

This is the detail that separates a proper job from a caulk job. We grind a clean reglet into the mortar joints, following the joint line up the chimney in steps, insert the counter-flashing's bent edge into the groove, wedge it mechanically, and seal the joint with the right sealant — used as a gasket inside a groove, not as glue on a surface. Counter-flashing installed this way is held by the chimney itself and sheds water over the step flashing below it for decades.

4Crickets and saddles for wide chimneys

A chimney more than about 30 inches wide creates a dam on its uphill side, where snow, ice, and debris pile up and water ponds. Building convention and modern code guidance call for a cricket: a small peaked saddle framed behind the chimney that splits the flow and sends it around both sides. We fabricate and flash crickets on chimneys that never had one — common on the older housing stock around Georgetown — and rebuild failed ones. If your leak shows up on the chimney's high side, a missing cricket is a prime suspect.

5Material selection and upgrades

We work in aluminum, galvanized and stainless steel, copper, and lead-coated copper, and we will tell you honestly where each belongs. Aluminum is economical but should not sit against damp mortar for the long haul; copper costs more and can outlive two roofs; stainless shrugs off the coastal salt air that eats galvanized coatings in a decade. On historic homes we match existing copper work rather than mixing metals. The right choice depends on your roof's age, your budget, and your exposure — a coastal cape and an inland colonial do not get the same recommendation.

6Reglet repointing and roof integration

Flashing repair is masonry work as much as metal work. We repoint the joints we cut, match mortar color as closely as the wall allows, and address crumbling joints adjacent to the flashing line while we are up there — there is no sense seating new metal into failing mortar. We also coordinate cleanly with roofers: if your roof is being replaced, we can handle the chimney intersection as part of that project, and if we find shingle or decking problems beyond the flashing, we document them for your roofing contractor rather than pretending they do not exist.

How We Diagnose and Fix It

It is tempting to skip diagnosis and jump straight to the fix, especially when a symptom seems self-explanatory. Resist that. Chimney symptoms overlap heavily: a white haze on brick, a musty smell, and a damp firebox can each stem from three or four different causes, and each cause has a different correct repair at a very different price. Contractors who quote significant work sight-unseen are guessing — and when the guess is wrong, you pay for the repair that did not solve the problem, then pay again for the one that does. A structured inspection per NFPA 211 costs a fraction of any meaningful repair and converts the project from speculation to evidence. In chimney work, the cheapest money you will ever spend is the money that ensures you fix the right thing.

Masonry repairs succeed or fail on materials and prep, not just workmanship. Repointing — cutting out failed mortar joints and refilling them — only lasts when the new mortar matches the old in hardness; modern Portland-heavy mixes are actually too strong for older Massachusetts brick and cause the surrounding faces to spall. Crown work has its own rules: a proper crown is cast concrete with an overhang and drip edge, not a thin mortar wash troweled over the top course, and a badly failed crown gets rebuilt rather than endlessly patched. Spalled bricks are cut out and replaced individually where damage is contained. When flashing repair is on the table, ask the contractor what mortar type they intend to use and why — the answer tells you quickly whether you are dealing with a chimney specialist or a generalist.

Warning Signs to Watch For

Water stains on ceilings or walls adjacent to the chimney, especially after wind-driven rain.
Visible tar or roofing cement smeared around the chimney's base — evidence of a previous shortcut repair.
Rust streaks running from the chimney base down across the shingles.
Lifted, bent, or missing pieces of flashing after a windstorm.
Visible gaps between the counter-flashing and the mortar joint it should sit in.
Popped nails or loose fasteners along the flashing line.
Shingles that look wavy, curled, or spongy in the courses beside the chimney.
Attic sheathing that is dark, damp, or delaminating around the chimney — especially on its uphill side.
Leaks that appear during nor'easters but not during gentle vertical rain.
Moss or algae concentrated right at the roof-to-chimney intersection.

Why This Matters in Georgetown

Georgetown pairs a compact antique center — including the 1670 Brocklebank house — with rural roads of farmhouses, capes, and 1990s-2000s cul-de-sac colonials. Older homes along East Main and North streets carry original brick center chimneys, while much of the newer stock west of the Square uses prefab fireplaces. Wood and pellet stoves are common supplements throughout town.

This is quiet upper Essex County, where winters bite harder than they do inside Route 128 and plenty of households keep a stove running from October to April. Homes bordering the Georgetown-Rowley State Forest see steady wildlife pressure on uncapped flues. It is exactly the kind of town where an annual sweep is genuinely used, not just recommended.

Nor'easters give chimneys in Georgetown a beating that ordinary storms never match. These coastal systems drive rain and snow horizontally for hours at a time, forcing water against the sides of a chimney rather than politely down onto its cap. Wind-driven rain exploits every weakness: hairline cracks in the crown, thin spots in mortar joints, and lifted flashing at the roofline all become entry points under that kind of pressure. Homeowners often discover the aftermath weeks later, as a ceiling stain near the chimney or a damp, smoky odor in the firebox. After a hard nor'easter season, a careful inspection of the crown, flashing, and masonry is not paranoia; it is how storm damage gets caught while the fix is still small.

What It Typically Costs

An inspection is the least expensive service a chimney company offers and the one that determines everything else, so it is worth understanding what you are paying for. A proper inspection is methodical: firebox, damper, smoke chamber, accessible flue, crown, cap, flashing, and exterior masonry, all documented with photographs. Where conditions warrant, a video scan of the flue interior shows what no flashlight can, including cracked tiles and failed joints deep in the stack. The report you receive should let you make decisions calmly, with evidence, ranked by urgency. Paying for that clarity once a year, as NFPA 211 recommends, is what allows every other chimney dollar you spend to be spent on the right thing.

Why Call Upside Down Chimney Sweeps

We built this company on the belief that chimney work should follow written standards, not folklore. Our sweeping and inspection procedures track NFPA 211, the National Fire Protection Association's standard for chimneys, fireplaces, and vents, along with the best practices promoted by the Chimney Safety Institute of America. That means we do not eyeball a flue and pronounce it fine; we examine accessible portions methodically, note the condition of liners, crowns, caps, and flashing, and classify creosote honestly by stage. Standards protect you in a second way, too: when we recommend a repair, we can point to the specific condition and the specific guidance behind the recommendation, so you are never asked to take an expensive claim on faith.

Frequently Asked Questions

What is chimney flashing, exactly?

Flashing is the layered sheet-metal system that waterproofs the joint where your chimney passes through the roof. Because the roof structure and the masonry move independently, no rigid or glued seal can survive there. Instead, flashing sheds water by overlapping: step flashing woven into the shingle courses carries water down the roof plane, and counter-flashing embedded in the chimney's mortar joints covers the tops of those steps so water running down the brick is thrown clear. Add an apron on the downhill face and a back pan or cricket uphill, and every side of the chimney has a gravity-fed drainage path. No adhesive is doing the real work — the geometry is.

What is the difference between step flashing and counter-flashing?

They are two layers with two jobs. Step flashing belongs to the roof: individual L-shaped pieces, one per shingle course, each tucked under a shingle and lapped over the piece below, fastened to the roof deck. It handles water flowing down the roof plane. Counter-flashing belongs to the chimney: pieces set into grooves cut in the mortar joints, bent down over the step flashing's vertical legs. It handles water flowing down the masonry face. The critical detail is that the two layers overlap without being attached to each other, so the roof and the chimney can move independently through the seasons without tearing the seal open.

Why not just seal it with roofing tar?

Roofing cement is a bandage, and everyone in this trade knows it. It bonds poorly to dusty masonry, turns brittle in the cold, shrinks away from edges within a couple of seasons, and — the part homeowners rarely hear — it can trap water behind it, holding moisture against the mortar through freeze-thaw cycles and accelerating the very damage it was hiding. It also buries the evidence, so the next diagnosis takes longer and costs more. We remove tar patches; we do not add to them. A proper counter-stepped metal system costs more on the day it is installed and dramatically less over the life of your roof.

Should I call a roofer or a chimney company for a flashing leak?

It is genuinely a boundary trade, which is why homeowners get bounced between the two. Roofers are excellent on the shingle side but often surface-mount counter-flashing with caulk rather than cutting it into the mortar, because masonry is not their trade. A chimney company that does masonry can cut reglets, repoint, and judge whether the leak is actually the crown or the brick rather than the flashing at all. We handle the full intersection and coordinate with your roofer when the job crosses into the roof field. Whoever you hire, ask one question: will the counter-flashing be let into the mortar joint? If the answer involves caulk, keep calling.

Which flashing metal is best, especially near the coast?

For most inland Greater Boston homes, aluminum or galvanized steel is serviceable and economical, but both have limits: aluminum reacts with damp mortar over time, and galvanized coatings fail early in salt air. Within a few miles of the ocean we push toward stainless steel or copper — coastal exposure corrodes cheap metal astonishingly fast, and we regularly replace galvanized flashing barely fifteen years old in shoreline towns. Copper is the premium choice everywhere: it forms beautifully, ages to a quiet brown, and routinely outlasts two shingle roofs. On historic homes in and around Georgetown, matching existing copper work is usually the right call both structurally and visually.

What is a cricket, and does my chimney need one?

A cricket, or saddle, is a small peaked structure built on the uphill side of a chimney to split water and snow around it instead of letting the chimney act as a dam. Modern building practice calls for one when the chimney is wider than about 30 inches across the slope. Without a cricket, the high side collects leaves, snowpack, and ponded water, and that standing load eventually beats any flat back pan. Many chimneys on older Massachusetts homes were built without one, which is why chronic high-side leaks are so common here. If your stains are on the uphill side of the chimney, ask us to check for this first.

How long does the repair take, and how long will it last?

Most full flashing rebuilds are a one-day job; targeted repairs of a single failed section often take a few hours. Weather matters — we want dry shingles, workable temperatures for sealants and mortar, and safe footing, so winter scheduling can shift with the forecast. As for longevity: properly counter-stepped metal set into sound mortar should last as long as the roof itself, and copper considerably longer. The honest caveat is the surrounding masonry — flashing set into crumbling joints will never reach its potential, which is why we repoint the reglet line as part of the job rather than treating it as an upsell.

My roof is being replaced — should the flashing be redone at the same time?

Yes, almost always, and the timing is a gift: with the shingles off, the entire intersection is exposed, membrane can be run properly, and new step flashing costs the least it ever will. Reusing old step flashing under a new roof is a common corner-cut we would talk you out of — thirty-year shingles deserve better than twenty-year-old metal. Coordinate the sequence: we can cut reglets and set counter-flashing right after the roofer finishes the field, or handle the full chimney intersection ourselves as part of the project. Call (781) 653-5644 before the roofing crew starts and we will slot the chimney work into their schedule.

Get It Handled Today

If something prompted you to read this far, a smell, a stain, a sluggish draft, a chunk of mortar in the firebox, treat it as your chimney asking for help while the help is still simple. Small chimney problems in Georgetown do not stay small through many Massachusetts winters; water and freeze-thaw cycles see to that. Call Upside Down Chimney Sweeps at (781) 653-5644 and describe what you have noticed. We will tell you honestly whether it sounds urgent, get you scheduled accordingly, and put trained eyes on the actual problem instead of guesses. Acting on an early sign is the cheapest chimney decision you will ever make, and it starts with a single call.

Serving Georgetown Same-Week

Our Melrose shop is 24 miles from Georgetown. Call (781) 653-5644 for fast scheduling.

Call (781) 653-5644 Email Us

Mon–Sat: 7:00 AM – 7:00 PM · Emergency service available